rf-wm-3235b1 is an rf module based on ti lower-power soc cc3235sf with built-in dual-band wi-fi connectivity. it integrates a 40 mhz crystal, 32.768 khz rtc clock, rf filters, diplexer, and two physical separated on-chip mcus: arm® cortex®-m4 mcu with a user-dedicated 256 kb of ram, an embedded 1 mb flash and an external plug-in 4 mb flash, network processor for running wi-fi and internet logical layers.

rf-star low power consumption 2.4 ghz wlan and 5 ghz dual-band wifi module cc3235 

 

rf-wm-3235b1 is an rf module based on ti lower-power soc cc3235sf with built-in dual-band wi-fi connectivity. it integrates a 40 mhz crystal, 32.768 khz rtc clock, rf filters, diplexer, and two physical separated on-chip mcus: arm®cortex®-m4 mcu with a user-dedicated 256 kb of ram, an embedded 1 mb flash and an external plug-in 4 mb flash, network processor for running wi-fi and internet logical layers. it features 802.11 a/b/g/n: 2.4 ghz and 5 ghz support, 2.4 ghz coexistence with bluetooth low energy radio, improved fast scan, hostless mode for offloading template packet transmissions and application features of small size, robust connection distance, and rigid reliability.

 

 

table 1. the pin diagram of rf-wm-3235b1

pin

name

function

description

1

gnd

gnd

ground

2

gnd

gnd

ground

3

gpio10

gpio

gpio

4

gpio11

gpio

gpio

5

gpio14

gpio

gpio

6

gpio15

gpio

gpio

7

gpio16

gpio

gpio

8

gpio17

gpio

gpio

9

gpio12

gpio

gpio

10

gpio13

gpio

gpio

11

gpio22

gpio

gpio

12

jtag­_tdi

tdi

jtag interface: data input

13

flash_miso

i

serial flash interface: spi data in

14

flash_csn

cs

serial flash interface: spi chip select

15

flash_clk

clk

serial flash interface: spi clock

16

gnd

gnd

ground

17

flash_mosi

o

serial flash interface: spi data out

18

jtag_tdo

tdo

jtag interface: data output

19

gpio28

gpio

gpio

20

nc

/

no connect

21

jtag_tck

tck

jtag interface: clock

22

jtag_tms

tms

jtag interface: mode select

23

sop2

sop

configuration sense-on-power

24

sop1

sop

configuration sense-on-power and 5 ghz switch control

25

gnd

gnd

ground

26

gnd

gnd

ground

27

gnd

gnd

ground

28

gnd

gnd

ground

29

gnd

gnd

ground

30

gnd

gnd

ground

31

rf_abg

rf out

rf bg band: 2.4 ghz tx, rx

rf bg band: 5 ghz tx, rx

32

gnd

gnd

ground

33

nc

/

no connect

34

sop0

sop

configuration sense-on-power and 5 ghz switch control

35

nreset

reset

master chip reset input. active low input.

36

vbat_reset

reset

vbat reset input. active low input.

37

vbat1

power

power supply: 2.7 v ~ 3.6 v, recommend to 3.3 v

38

gnd

gnd

ground

39

nc

/

no connect

40

vbat2

power

power supply

41

nc

/

no connect

42

gpio30

gpio

gpio

43

gnd

gnd

ground

44

gpio0

gpio

gpio

45

nc

/

no connect

46

gpio1

gpio

gpio

47

gpio2

gpio

analog input (1.5 v max.) or gpio

48

gpio3

gpio

analog input (1.5 v max.) or gpio

49

gpio4

gpio

analog input (1.5 v max.) or gpio

50

gpio5

gpio

analog input (1.5 v max.) or gpio

51

gpio6

gpio

gpio

52

gpio7

gpio

gpio

53

gpio8

gpio

gpio

54

gpio9

gpio

gpio

55

gnd

/

thermal ground

56

gnd

/

thermal ground

57

gnd

/

thermal ground

58

gnd

/

thermal ground

59

gnd

/

thermal ground

60

gnd

/

thermal ground

61

gnd

/

thermal ground

62

gnd

/

thermal ground

63

gnd

/

thermal ground

 
application

 

our services

 

 

our company

 

packaging & shipping

 

faq

 

contact us


recommended footprint

图片关键词


pin attributes

图片关键词

pin

name

function

description­­

pin1

gnd

-

ground

pin2

gnd

-

ground

pin3

gpio10

i/o

gpio

pin4

gpio11

i/o

gpio

pin5

gpio14

i/o

gpio

pin6

gpio15

i/o

gpio

pin7

gpio16

i/o

gpio

pin8

gpio17

i/o

gpio

pin9

gpio12

i/o

gpio

pin10

gpio13

i/o

gpio

pin11

gpio22

i/o

gpio

pin12

jtag_tdi

i/o

jtag tdi input. leave unconnected if not used on product

pin13

flash_spi_miso

i

external serial flash programming: spi data in

pin14

flash_spi_ncs_in

i

external serial flash programming: spi chip select (active low)

pin15

flash_spi_clk

i

external serial flash programming: spi clock

pin16

gnd

-

ground

pin17

flash_spi_mosi

o

external serial flash programming: spi data out

pin18

jtag_tdo

i/o

jtag tdo output. leave unconnected if not used on product

pin19

gpio28

i/o

gpio

pin20

nc

-

-

pin21

jtag_tck

i/o

jtag tck input. leave unconnected if not used on product.(2)
an internal 100 k
ω pull down resistor is tied to this pin.

pin22

jtag_tms

-

jtag tms input. leave unconnected if not used on product.

pin23

sop2

-

an internal 100 kω pull down resistor is tied to this sop pin. an
external 10 kω resistor is required to pull this pin high. see
section 6.11.1 for sop[2:0] configuration modes.

pin24

sop1

-

an internal 100 kω pull down resistor is tied to this sop pin. an
external 10 kω resistor is required to pull this pin high. see
section 6.11.1 for sop[2:0] configuration modes.

pin25

gnd

-

ground

pin26

gnd

-

ground

pin27

gnd

-

ground

pin28

gnd

-

ground

pin29

gnd

-

ground

pin30

gnd

-

ground

pin31

rf_abg

i/o

ground

pin32

gnd

-

ground

pin33

nc

-

-

pin34

sop0


an internal 100 kω pull down resistor is tied to this sop pin. an
external 10 kω resistor is required to pull this pin high. see
section 6.11.1 for sop[2:0] configuration modes.

pin35

nreset

i

there is an internal, 100 kω, pull-up resistor option from the
nreset pin to vbat_reset. note: vbat_reset is not
connected to vbat1 or vbat2 within the module. the following
connection schemes are recommended:
• connect nreset to a switch, external controller, or host,
only if nreset will be in a defined state under all operating
conditions. leave vbat_reset unconnected to save
power.
• if nreset cannot be in a defined state under all operating
conditions, connect vbat_reset to the main module
power supply (vbat1 and vbat2). due to the internal pullup
resistor a leakage current of 3.3 v / 100 kω is expected.

pin36

vbat_reset

-

pin37

vbat1

power

power supply for the module, must be connected to battery (2.3
v to 3.6 v)

pin38

gnd

-

ground

pin39

nc

-

-

pin40

vbat2

power

power supply for the module, must be connected to battery (2.3
v to 3.6 v)

pin41

nc

-

-

pin42

gpio30


gpio

pin43

gnd


ground

pin44

gpio30



pin45

nc

-

-

pin46

gpio1

i/o

gpio

pin47

gpio2

i/o

gpio

pin48

gpio3

i/o

gpio

pin49

gpio4

i/o

gpio

pin50

gpio5

i/o

gpio

pin51

gpio6

i/o

gpio

pin52

gpio7

i/o

gpio

pin53

gpio8

i/o

gpio

pin54

gpio9

i/o

gpio

pin55

gnd

-

thermal ground

pin56

gnd

-

thermal ground

pin57

gnd

-

thermal ground

pin58

gnd

-

thermal ground

pin59

gnd

-

thermal ground

pin60

gnd

-

thermal ground

pin61

gnd

-

thermal ground

pin62

gnd

-

thermal ground

pin63

gnd

-

thermal ground


网站地图